Updated: 24-SEP-2003 (Use your browsers' Reload button to ensure you're viewing the most recent version)
VMS712_VX1-V0100 Alpha 7.1-2 3DLabs Graphics Controller ECO Summar
Copyright (c) Compaq Computer Corporation 2000. All rights reserved.
New Kit Date : 06-Feb-2001
Modification Date: Not Applicable
Modification Type: New Kit
OP/SYS: OpenVMS Alpha V7.1-2
COMPONENT: 3DLabs OXYGEN Graphics Controller
SOURCE: Compaq Computer Corporation
ECO INFORMATION:
ECO Kit Name: VMS712_VX1-V0100
ECO Kits Superseded by This ECO Kit: None
ECO Kit Approximate Size: 816 Blocks
Kit Applies To: OpenVMS Alpha 7.1-2
System/Cluster Reboot Necessary: Yes
Rolling Re-boot Supported: Yes
Installation Rating: INSTALL_UNKNOWN
Kit Dependencies:
The following table lists information on which software kits
are required to install 3Dlabs OXYGEN VX1 PCI Graphics Controller
support on your Alpha platform.
-----------------------------------------------------------------------------
OpenVMS Version | Required Kit(s)
-----------------------------------------------------------------------------
V7.3 | No separate software kits are necessary. The 3Dlabs
| OXYGEN VX1 PCI Graphics Controller support software
| will be fully integrated into OpenVMS Version 7.3
-----------------------------------------------------------------------------
V7.2-1H1 | VMS721H1_VX1-V0100 (or later)
| VMS721H1_UPDATE-V0300 (or later)
| VMS721H1_CPU2208-V0100 (or later)
-----------------------------------------------------------------------------
V7.2-1 | VMS721_VX1-V0100 (or later)
| VMS721_PCSI-V0100 (or later)
| VMS721_UPDATE-V0100 (or later)
| VMS721_CPU2208-V0100 (or later)
-----------------------------------------------------------------------------
V7.1-2 | VMS712_VX1-V0100 (or later)
| VMS62TO71U2_PCSI-V0200 (or later)
| VMS712_UPDATE-V0300 (or later)
| VMS712_CPU2208-V0100 (or later)
-----------------------------------------------------------------------------
Prior to V7.1-2 | 3Dlabs OXYGEN VX1 PCI Graphics Controller support
| is not available on versions of OpenVMS prior to V7.1-2
Note: Where applicable the OpenVMS PCSI kit should be installed first.
Installation order of any of the other kits is not important.
ECO KIT SUMMARY:
An ECO kit exists for 3Dlabs OXYGEN VX1 PCI Graphics Controller on OpenVMS
Alpha V7.1-2. This kit addresses the following problems:
Problems Addressed In VMS712_VX1-V0100:
o Provide Functionality to enable use of the 3Dlabs OXYGEN VX1 PCI Controller
two-dimensional (2D) support software
RELATED ARTICLES:
Detailed articles describing the problems listed above may exist in
the OPENVMS database(s). To view these articles,
open the appropriate product database and perform a query using either
of the following search strings: 'VMS712_VX1-V0100' or 'VMS712_VX1'.
ECO KIT ORDERING INSTRUCTIONS:
If after an evaluation you wish to obtain this kit, request it
electronically using the appropriate Advanced Electronic Services
(AES) Service Tool. If you are not familiar with how to request
kits electronically, open the DIA, WIS or DSNLINK database and
review the article entitled:
[AES] How To Electronically Request ECO Kits Using Service Tools
INSTALLATION NOTES:
The images in this kit will not take effect until the system is
rebooted. If there are other nodes in the VMScluster, they must
also be rebooted in order to make use of the new image(s).
If it is not possible or convenient to reboot the entire cluster at
this time, a rolling re-boot may be performed.
o OpenVMS Version 7.3 Installation
For OpenVMS Version 7.3 and higher, the 3Dlabs OXYGEN VX1 PCI Graphics
Controller support software will be automatically loaded following
installation Of OpenVMS and becomes active when the operating system is
booted. No other action needs to be taken by the system operator.
o OpenVMS Versions 7.1-2, 7.2-1, and 7.2-1H1
After the appropriate kits for your version of OpenVMS are downloaded,
the 3Dlabs OXYGEN VX1 PCI Graphics Controller support software is
installed by using the POLYCENTER Software installation utility. To
install the kit, log into the SYSTEM account, and type the following
command at the DCL prompt:
PRODUCT INSTALL VMS***_VX1 /SOURCE=[location of Kit]
*** = the version of OpenVMS that is running on the system, i.e. 712,
721 or 721H1. For example, for a V7.2-1H1 system you would
enter the command:
PRODUCT INSTALL VMS721H1_VX1 /SOURCE=[location of Kit]
The location of the kit may be a tape drive, CD, or a disk directory
that contains the kit.
To install a PCSI or UPDATE kit, follow the installation directions
included in that kit's Release Notes.
If you ordered the 3Dlbas OXYGEN VX1 PCI Graphics Controller separately,
then follow the additional instructions provided with the module to
install the appropriate support software contained on the CD-ROM
shipped with the module.
Additional help on installing PCSI kits can be found by typing
HELP PRODUCT INSTALL at the system prompt.
All trademarks are the property of their respective owners.
==========================================================================
| Table of Kit Image Information |
+----------------------------+----------+-----------------+--------------+
| | Overall | Image File | Image Link |
| Image Name | Checksum | Identification | Date/Time |
+----------------------------+----------+-----------------+--------------+
| DECW$SERVER_DDX_P3.EXE | C53E8FCE | DW V7.1-001214 | 14-DEC-2000 |
| | | 09:23:24.26 |
+----------------------------+----------+-----------------+--------------+
| SYS$GFDRIVER.EXE | E76F8A85 | DW V7.1-001206 | 6-DEC-2000 |
| | | 08:22:45.68 |
+----------------------------+----------+-----------------+--------------+
|
